Masana Energy Solutions HSS Customer Guide

chemical-resistant gloves (tested to EN374) in combination with 'basic' employee training. Avoid carrying out activities involving exposure for more than 1 hour per day. or Ensure material transfers are under containment or extract ventilation. Refuelling: Ensure material transfers are under containment or extract ventilation. Wear chemical-resistant gloves (tested to EN374) in combination with 'basic' employee training. Avoid carrying out activities involving exposure for more than 1 hour per day. Use in fuel (Closed systems): Wear chemical-resistant gloves (tested to EN374) in combination with 'basic' employee training. Equipment cleaning and maintenance: Provide a good standard of general ventilation (not less than 3 to 5 air changes per hour). Wear chemical-resistant gloves (tested to EN374) in combination with specific activity training. Drain down system prior to equipment break-in or maintenance. Retain drain-downs in sealed storage pending disposal or for subsequent recycle. Clear spills immediately. Section 2.2: Control of environmental exposure Product characteristics: Substance is complex UVCB. Predominantly hydrophobic Frequency and duration of use: Continuous release Environment factors not influenced by risk management: Technical conditions and measures at process level (source) to prevent release: Common practices vary across sites thus conservative process release estimates used. Technical on-site conditions and measures to reduce or limit discharges, air emissions and releases to soil: Risk from environmental exposure is driven by humans via indirect exposure (primarily ingestion). No wastewater treatment required. Organisational measures to prevent/limit release from site: Do not apply industrial sludge to natural soils. Sludge should be incinerated, contained or reclaimed Conditions and measures related to sewage treatment plant: Not applicable as there is no release to wastewater. Conditions and measures related to external treatment of waste for disposal: Combustion emissions limited by required exhaust emission controls. Combustion emissions considered in regional exposure assessment. External treatment and disposal of waste should comply with applicable local and/or national regulations. Conditions and measures related to external recovery of waste: This substance is consumed during use and no waste from the substance is generated. Emission days 365 Local freshwater dilution factor 10 Local marine water dilution factor 100 Treat air emission to provide a typical removal efficiency of Not applicable. Treat on-site wastewater (prior to receiving water discharge) to provide the required removal efficiency of ≥ 0.0% If discharging to municipal sewage treatment plant, provide the required on-site wastewater removal efficiency of ≥ 0.0% Estimated substance removal from wastewater via on-site sewage treatment EC number ... % | EC number ... % 265-045-2 … 95.1 | 265-082-4 … 87.6 265-058-3 … 90.4 | 269-777-3 … 94.0 265-064-6 … 92.5 | 270-675-6 … 94.2 265-076-1 … 92.7 | 273-263-4 … 94.0 265-081-9 … 93.9 | 295-511-0 … 93.2 Total efficiency of removal from wastewater after on-site and off-site (municipal treatment plant) RMMs EC number ... % | EC number ... % 265-045-2 … 95.1 | 265-082-4 … 87.6 265-058-3 … 90.4 | 269-777-3 … 94.0 265-064-6 … 92.5 | 270-675-6 … 94.2 265-076-1 … 92.7 | 273-263-4 … 94.0 265-081-9 … 93.9 | 295-511-0 … 93.2 Maximum allowable site tonnage (M Safe ) based on release following total wastewater treatment removal EC number ... kg/day | EC number ... kg/day 265-045-2 … 9.8E+02 | 265-082-4 … 5.8E+02 265-058-3 … 6.9E+02 | 269-777-3 … 4.1E+02 265-064-6 … 1.4E+02 | 270-675-6 … 3.8E+03 265-076-1 … 2.1E+02 | 273-263-4 … 2.0E+02 265-081-9 … 7.1E+04 | 295-511-0 … 1.4E+02 Assumed on-site sewage treatment plant flow 2.0E+03 (m3/d) 28/38 Use in fuel (Heavy fuel oil) - Professional Fuel Oil, residual